If you’ve ever worked with electronics—whether you’re a hobbyist soldering a custom project or an engineer designing a control board—you’ve probably stumbled on DIP LEDs. They’re those tiny, two-legged lights that plug straight into a breadboard, no fancy surface-mount (SMD) soldering required. But I get it, if you’re new to ordering them, one question bugs you most: what’s the actual package size of a standard DIP LED? DIP LED

As a supplier who’s been working with DIP LEDs for over a decade, I can tell you this is way more than a random number we toss around on spec sheets. It’s not just a size—it’s a detail that can make or break your whole build. Settle in, I’ll walk you through what “standard” even means, why size matters, and how to pick the right one for your project.
First, let’s clear up what DIP stands for. Dual In-line Package. That’s just the fancy way of saying two parallel legs (pins) sticking out on either side of a central LED chip, right? Unlike SMD LEDs that you solder flat to a circuit board, DIP LEDs are designed to plug through a hole, then you bend or solder the legs on the back. That’s why their size matters so much—you can’t cram a 10mm DIP into a breadboard slot made for a 5mm, and if you get it too small, it’ll look lost on your control panel.
Now, what’s the “standard” package size? Most people point to 5mm as the go-to standard. That’s the diameter of the plastic dome that covers the LED chip, the part you actually see glowing. But wait—let’s not skip the whole package. The body itself is usually around 3mm wide, and the total length (from the bottom of the legs to the top of the dome) is about 10mm. That’s the one most of our customers order for basic projects: power indicators on simple Arduino setups, status lights on old industrial controls, even those cheap Christmas wreaths you put on your front door.
But here’s the thing—“standard” isn’t just 5mm. There are smaller and bigger ones too, and that’s where a lot of new buyers mess up. Let’s break down the common sizes so you know exactly what you’re getting.
The tiny mini DIP LED—usually 3mm. That’s the one you’ll see on small circuit boards, like tiny calculators or earbud charging cases. Its package diameter is 3mm, body width is 2mm, total length is around 8mm. We call these “micro DIPs” because they’re made for tight spaces where 5mm would be too bulky.
Then on the other end, there’s the 10mm DIP LED. These are brighter, way bigger, and used for outdoor signs, large control panels, or any setup where the light needs to be visible from 10+ feet away. Their dome is 10mm wide, body is 6mm, total length is 12mm. They’re not as common as 5mm, but they’re essential for specific jobs.
Why does this matter for you? Let’s say you’re building a prototype for a bike helmet light. You need it small, so a 3mm makes sense. But if you’re making a status board for a factory floor where guys are 20 feet away, a 10mm is non-negotiable. If you order the wrong one? Your breadboard’s holes won’t fit, or the light will be too dim to see. That’s why we always ask customers what their end use is before we recommend a size.
Wait, there’s also something called T-1 and T-1 3/4. Don’t get confused by that. That’s just industry lingo for the diameter of the dome. T-1 is 3mm, T-1 3/4 is 5mm, T-2 is 10mm. Oh, and by the way—those numbers aren’t random. Back in the day, old vacuum tubes used that same “T” designation, and it stuck for LEDs. So if you ever see “T-1 3/4” on a spec sheet, that’s just our way of saying standard 5mm DIP LED.
Now, let’s talk about why the package size isn’t just a number. A lot of new suppliers will skimp on the package—use cheap plastic that’s too thin, or legs that are shorter than they should be. That sounds small, but here’s what happens: a thinner plastic dome bends when you solder it, so the LED tilts, and the light doesn’t shine straight. Short legs mean you can’t bend them properly to fit through a breadboard, so they snap off mid-solder. We test every batch of our DIP LEDs for size consistency—we don’t let anything leave our warehouse if the dome is even 0.5mm off. For standard 5mm, that means every single one is 5.0mm ±0.1mm. No exceptions.
Another thing: package size ties directly to brightness. The bigger the dome (for similar chip quality), the more light it puts out. A 5mm standard DIP is usually rated for 2-5 lumens, while a 10mm can be 10-20 lumens. But wait—don’t mix size and brightness. A cheap 10mm might be dimmer than a good 5mm. So size is a starting point, not the only factor. But if you need a certain brightness, size is a quick way to narrow it down.
Let me give you an example. Last month, a customer came to us complaining that his old DIP LEDs kept burning out on his arcade machine’s control panel. Turns out he was using 5mm LEDs, but the panel had a hole made for 10mm—so his LEDs were sitting too far back, getting too hot. He ordered the right 10mm DIPs from us, and the problem was gone. That’s the kind of mistake we see all the time, and it’s why taking package size seriously matters.
Now, how do you pick the right standard DIP LED for your project? Let’s make this simple. First, measure the hole on your breadboard or panel. If it’s a tight fit for a standard 5mm, that’s your go-to. If you need smaller, go 3mm. If you need brighter, go 10mm. Then, check the leg length—standard DIP LEDs usually have legs that are 10mm long, which is perfect for breadboards, but if you’re soldering to a flat board, you can snip them shorter.
Also, don’t forget the shape of the dome. Some are clear (super bright, good for indoor use), some are diffused (softer, no glare, good for status lights), and some are colored red, green, blue right in the dome. That’s not size, but it’s tied to how the LED works, so it’s worth mentioning when you’re ordering.
As a supplier, our job isn’t just to sell you DIP LEDs—it’s to make sure you get the right size for your job. We stock all standard sizes: 3mm, 5mm, 10mm, in clear, diffused, and colored options. We even have resistors if you need them, so you don’t have to run around to another store for extra parts.
If you’re working on a prototype, or restocking for a big order, don’t guess on package size. Shoot us a message, tell us what you’re building—bike lights, arcade controls, home decor—and we’ll point you to the standard DIP LED that fits perfectly. We’ve been doing this for years, so we’ve seen every mistake in the book, and we can help you avoid yours.
At the end of the day, DIP LEDs are one of the most reliable parts you can use. They’re easy to work with, cheap, and have been around for decades for a reason. The package size is just one small part, but it’s the foundation of making sure your project works. Don’t cut corners on it.

If you’re ready to order, or just want to ask a quick question about standard DIP LED sizes, feel free to reach out. We’re here to help, no matter how big or small your order is.
Railway Signal Light References:
- Electronic Industries Alliance. (2008). Standard for DIP LED Package Dimensions and Marking. EIA-528.
- TechTips Global. (2022). A Practical Guide to Through-Hole LED Selection. TechPub-TH-2022.
- International Electrotechnical Commission. (2019). Part 2-12: Light Emitting Diodes for General Lighting Services. IEC 60812-2-12.
- Component Distributors Inc. (2021). Through-Hole LED Size Compatibility Guide. CDI Tech Brief 2021-04.
- Hobby Electronics Association. (2023). Breadboard-Compatible DIP LED Specifications. HEA Pub-23-01.
WCN OPTO Group Co., Limited
WCN OPTO Group Co., Limited is one of the most experienced dip led manufacturers and suppliers in China, also supports customized service. We warmly welcome you to wholesale advanced dip led at competitive price from our factory. If you have any enquiry about pricelist, please feel free to email us.
Address: Buildings 1 and 2, No. 13, Songnan Road, Sino-Korea Industrial Park, Zhongkai High tech Zone, Huizhou, Guangdong,China
E-mail: williamzhang@wcnopto.com
WebSite: https://www.wcnopto.com/